Peugeot 3008 Key Fob Problems
Peugeot's mid-sized 3008 SUV has a lot to offer. It's smooth to drive, looks great and has a large boot. But can it fend off strong competition in the most crowded sector of the market?
If your Peugeot key fob is not functioning, it may have been exposed to clean tap water or soapy water. It may be necessary to remove the battery and clean it using electronic cleaner or isopropyl alcohol.
Dead coin battery
Peugeot key fobs are powered by a coin-sized battery. The power used to control the remote locking system, as well as other features. This battery has a finite lifespan and can wear out over the course of years of usage. Voltage testing is a straightforward way to determine if the battery is defective. A multimeter is used to measure the voltage that is between the battery's plus and minus poles. This test will determine whether the battery is dead.
The receiver module could be the reason for your key fobs not functioning after having used your Peugeot 3008 for a long time. The receiver module is in charge of receiving radio frequency signals sent by the key fobs, and sending them to car systems. If the receiver module is damaged, it will not be able send commands to the other modules within the vehicle.
Sweat or moisture on the circuit board is another typical reason for a malfunctioning key fob. This can cause short circuits which drain the battery and disable the remote locking feature of the key fob. If this happens you must take your key fob in to a technician that specializes in chip level repairs.
Water damage
Water damage can cause problems, whether you dropped your keyfob in the swimming spa, washed it or left it outside in the rain. Water makes for a good conductor and can easily cause short circuits on the circuit board. It can also cause corrosion to metal connections on the key fob as well as other components. A wet circuit board can cause the battery to lose its charge.
If you have an additional key fob, you can use it to lock/unlock the Peugeot 3008 to rule out a dead coin-cell battery as the source of the issue. Another issue that could stop your key fob from working effectively is interference signals that interfere with the signal sent to the receiver module. These signals can be caused by various sources, including radio transmitters in the vicinity.
If you hear sloshing noises coming from your Peugeot 3008 while driving, this is likely caused by a blocked condensate drain of the evaporator. You can test this by blowing compressed air through the drain holes in your door. You can also use flexible wire to make the drain holes sway and wash away any dirt that has built up there. Air pockets can be indicated by sloshing noises.
Receiver module that is defective
The receiver module of the receiver module of a Peugeot 3008 is responsible for transmitting a remote keyless signal from the keyfob to the receiver inside the car. If this module is damaged, it may cause the car to not recognize the key fob. Other factors that can cause this issue are a dead battery water damage or interference with electronic devices that operate at the same frequency as the key fob. In these cases the car might display an error message saying "card not detected" on the display.
There are many ways to fix this issue. You can try to replace the battery or reprogram the key fob. You could also use a spare key to start the car. However, if your key fob isn't working after all these steps, it might be a chip malfunctioning.
It is best to get rid of the chip and clean it with rubbing alcohol and paper towel. If the chip is damaged, you must purchase a new one. peugeot key cutting come with an accessory for battery holders for coin cells that can be used with the most commonly used types of key fob batteries. These enclosures are customizable by using digital printing and CNC-machined cutouts. If your key fob was exposed to dirty or salted tap water, it is possible that the chip has become damaged.
Faulty keyless entry system
When you see the message "card not detected" It means that your vehicle is unable to receive a signal from your key fob. This could be due to many reasons including an insufficient or dead battery. The issue is usually resolved by pressing the start button on the key fob. In some instances however, you may have to take the key fob to a Peugeot dealership for additional repairs.
The first step to fix the issue with a Peugeot 3008 key fob that's not able to unlock or lock the doors is to test its battery. Batteries are the primary reason for a fob that is malfunctioning however there are a variety of other factors that could contribute to this issue as well. They include worn buttons, and water damage.
If your Peugeot key fob has been exposed to clean tapwater, it is a good idea to remove the battery. Then, dry the electronic components using paper towel. You can also employ a cleaner or isopropyl ethanol for this. It's best to change the fob when it has been exposed to salt water or soapy water.
If your key fob is still not working, you can try to reset it by disconnecting the battery that is 12 volts for about 15 minutes. Then reconnect the negative cable first, followed by the positive one.